Zema laser handle repair and replacement service

Zema laser handle repair service description:

This VS-MI-80-10-Zema stack is for 800W Zema laser handle repairing service. Please find the details in the following:

Oriental-laser focused on diode laser bar assembling for more than 16 years and we have seen various alma soprano diode laser stacks.Also we can use the same Jenoptik bar like Alma used to recondition the power the laser soprano power. And also we can repair other brand like Zema laser, Aroma Laser and also any china branded.

800W Zema laser handle 800W Zema laser handle 800W Zema laser handle

Zema laser handle repair service procedure

>Choice A: Send the old broken handpiece to our factory. We will do the process of checking , repairing, cleaning and etc. Then send the fresh new handpiece back to you.

>Choice B:  if you have basic assembly capacity, you can send the diode laser stack only to our factory. We remove the old bar and mount the new bar to recover the laser power of the stack. 

>Choice C: Measure your stack and confirm the water pipe hole and screw hole position. Then press the button below to buy a ready-made stack which is match your old handpiece. 

Zema laser handle repair service Advantages

>Save Money. Replace the broken diode stack only. Low cost and convenient

>Long lifetime.  we use diode laser bars from Germany also we have laser bar from USA dilas and Coherent.The newest Ausn mounting technology will be applied when repairing. After repair. The handpiece will be as a new one. lifetime is much longer than before

>All technical support available. We major in diode laser mounting, software, spare parts over 16 years. All the technologies about laser hair removal machine are open to you.                   

Zema laser handle repair service Specification

Model No VS-MI-80-10-Zema
Application Alma Soprano Handle Piece Repair And Replacement
Operation Mode CW
Number of submounts 10 Bars
Power per submounts 100W
Central wavelength at 25℃ 808 ± 5nm
Typical Operation current 90A
Typical Threshold current 15A
Maximum Operating Voltage 20V
Fast Axis Divergence (FWHM) 39º
Slow Axis Divergence (FWHM)
Expected lifetime >10000 Hours
Typical pitch per bar 1.8mm
Cooling  
Flow rate 0.3L/min ±10% / Bar
Water Temperature 25+-3°C
Water Quality Deionized 2-10 µs/cm, mixed bed ion exchanger,particle filter<25µm
cooling system Do not use any material that combination with copper would form galvanic elements

Zema laser handle repair service Dimension:

800W Zema laser handle

Zema laser handle repair service application:

800W Zema laser handle800W Zema laser handle 800W Zema laser handle 800W Zema laser handle

Any more question please kindly add my whatsapp 0086-18518945778.

 

Model D GTMH-500/300 laser handle replacement service

GTMH-500/300 laser handle replacement service description:

This 808nm hair removal handpiece model D has two kinds of version. one is 500W optical power with 10bars. Another is 300W optical power with 6pcs 50W diodelaser bars. The diode lasr bar stack which match this handpiece are VS-MA-50-10 Model C/GTHM-500 or VS-MA-50-6-A/GTHM-300/DVS-300. This kinds of handpiece can be bought or repair.

Most of this handpiece will be broken after 1-2millions shots. then the laser stack which is in it will burt out.

We remove the old burnt bar and replace with new bar. After that, the handpeice will become as a new one.

GTMH-500/300 laser handle replacement service procedure:

Chioce A: Send the old broken handpiece to our facatory. We will do the process of checking , repairing, cleanning and etc. Then send the fresh new handpiece back to you.

Chioce B: if you have basic assambly capacity, you can send the diode laser stack only to our factory. We remove the old bar and mount the new bar to recover the laser power of the stack.

Choice C: Measure your stack and comfrim the water pipe hole and screw hole position. Then press the button below to buy a ready-made stack which is match your old hadnpiece.

GTMH-500/300 laser handle replacement service Advantages

1.The newest Ausn mounting technology will be applied when repairing.

2.Diode laser bars are made in Germany

3.After repair. The handpiece will be as a new one. life time is much longer than before .

4.All technical support of hair removal machine is avaliable. Such as handpiece parts, electonic board, program, cooling and etc.

GTMH-500/300 laser handle replacement service Specifications:

Any more question please kindly add my whatsapp 0086-18518945778.

Model M 600W diode laser tip repairing service

600W diode laser tip repairing service description:

This diode laser hair removal handpiece model M is made of 5 or 6 pcs diode bar with micro channel cooler. The laser bar in this handpiece is VS-MI-100-6-FL-A

Whole handpiece is made in China.

Service mode: Repair the broken diode laser in the handpiece. Such as replace new laser stack, test TEC peltier, cleaning and so on.

600W diode laser tip repairing service procedure:

Chioce A: Send the old broken handpiece to our facatory. We will do the process of checking , repairing, cleanning and etc. Then send the fresh new handpiece back to you.

Chioce B: if you have basic assambly capacity, you can send the diode laser stack only to our factory. We remove the old bar and mount the new bar to recover the laser power of the stack.

Choice C: Measure your stack and comfrim the water pipe hole and screw hole position. Then press the button below to buy a ready-made stack which is match your old hadnpiece.

600W diode laser tip repairing service Advantages:

Save Money. Replace the broken diode stack only. Low cost and convenient.

Long life time. we use diode laser bars from Germany. The newest Ausn mounting technology will be applied when repairing. After repair. The handpiece will be as a new one. life time is much longer than before.

All technical support available. We major in diode laser mounting, software, spare parts over 16 years. All the technology are open to you.

600W diode laser tip repairing service specifications:

Any more question please contact my whatsapp 0086-18518945778

 

Model H 10 bars macro channel laser handle 500W for recondition

10 bars macro channel laser handle 500W description:

This 808nm hair removal handpiece model I is made of 10bars laser stack with 500W optic power. The laser bars in this handpiece is VS-MA-50-10 Model C/GTHM-500.

Most of this handpiece will be broken after 1-2millions shots. then the laser stack which is in it will burt out.

We remove the old burnt bar and replace with new bar. After that, the handpeice will become as a new one.

10 bars macro channel laser handle 500W procedure:

Chioce A: Send the old broken handpiece to our facatory. We will do the process of checking , repairing, cleanning and etc. Then send the fresh new handpiece back to you.

Chioce B: if you have basic assambly capacity, you can send the diode laser stack only to our factory. We remove the old bar and mount the new bar to recover the laser power of the stack.

Choice C: Measure your stack and comfrim the water pipe hole and screw hole position. Then press the button below to buy a ready-made stack which is match your old hadnpiece.

10 bars macro channel laser handle 500W Advantages

1.The newest Ausn mounting technology will be applied when repairing.

2.Diode laser bars are made in Germany

3.After repair. The handpiece will be as a new one. life time is much longer than before .

4.All technical support of hair removal machine is avaliable. Such as handpiece parts, electonic board, program, cooling and etc.

10 bars macro channel laser handle 500W Specifications:

Any more question please kindly add my whatsapp 0086-18518945778.

Model G diode laser handle 500W Maintanence service

laser handle 500W Maintanence service description:

This 808nm hair removal handpiece model G -China A is made of 10bars laser stack with 500W optic power.

Most of this handpiece will be broken after 1-2millions shots. then the laser stack which is in it will burt out.

We remove the old burnt bar and replace with new bar. After that, the handpeice will become as a new one.

laser handle 500W Maintanence service procedure

Chioce A: Send the old broken handpiece to our facatory. We will do the process of checking , repairing, cleanning and etc. Then send the fresh new handpiece back to you.

Chioce B: if you have basic assambly capacity, you can send the diode laser stack only to our factory. We remove the old bar and mount the new bar to recover the laser power of the stack.

Choice C: Measure your stack and comfrim the water pipe hole and screw hole position. Then press the button below to buy a ready-made stack which is match your old hadnpiece.

laser handle 500W Maintanence service Advantages

1.The newest Ausn mounting technology will be applied when repairing.

2.Diode laser bars are made in Germany

3.After repair. The handpiece will be as a new one. life time is much longer than before .

4.All technical support of hair removal machine is avaliable. Such as handpiece parts, electonic board, program, cooling and etc.

laser handle 500W Maintanence service Specifications:

Any more question please contact Danny WhatsApp 0086-18518945778

Model X for 808nm 500W laser diode handpiece recondition

500W laser diode handpiece recondition descrition:

This diode laser hair removal handpiece model X is made of 5pcs diode bar with micro channel cooler. The laser bar in this handpiece is VS-MI-100-6-FL-A

Whole handpiece is made in China.

Service mode: Repair the broken diode laser in the handpiece. Such as replace new laser stack, test TEC peltier, cleaning and so on.

500W laser diode handpiece recondition procedure

Chioce A: Send the old broken handpiece to our facatory. We will do the process of checking , repairing, cleanning and etc. Then send the fresh new handpiece back to you.

Chioce B: if you have basic assambly capacity, you can send the diode laser stack only to our factory. We remove the old bar and mount the new bar to recover the laser power of the stack.

Choice C: Measure your stack and comfrim the water pipe hole and screw hole position. Then press the button below to buy a ready-made stack which is match your old hadnpiece.

500W laser diode handpiece recondition Advantages

1.Save Money. Replace the broken diode stack only. Low cost and convenient

2.Long life time. we use diode laser bars from Germany. The newest Ausn mounting technology will be applied when repairing. After repair. The handpiece will be as a new one. life time is much longer than before

3.All technical support available. We major in diode laser mounting, software, spare parts over 16 years. All the technology are open to you.

500W laser diode handpiece recondition Specifications:

Any more question please kindly add my whatsapp 0086-18518945778.

Model W big spot ADSS 1600W laser handle refurbishing service

ADSS 1600W laser handle refurbishing description:

This 808nm hair removal handpiece model W-ADSSbigspot is made of 32bars laser stack with 1600W optic power. The laser bar stack in this handpiece is VS-MA-50-32(2×16) Model A

Most of this handpiece will be broken after 1-2millions shots. then the laser stack which is in it will burt out.

We remove the old burnt bar and replace with new bar. After that, the handpeice will become as a new one.

ADSS 1600W laser handle refurbishing procedure

Chioce A: Send the old broken handpiece to our facatory. We will do the process of checking , repairing, cleanning and etc. Then send the fresh new handpiece back to you.

Chioce B: if you have basic assambly capacity, you can send the diode laser stack only to our factory. We remove the old bar and mount the new bar to recover the laser power of the stack.

Choice C: Measure your stack and comfrim the water pipe hole and screw hole position. Then press the button below to buy a ready-made stack which is match your old hadnpiece.

ADSS 1600W laser handle refurbishing Advantages

1.The newest Ausn mounting technology will be applied when repairing.

2.Diode laser bars are made in Germany

3.After repair. The handpiece will be as a new one. life time is much longer than before .

4.All technical support of hair removal machine is avaliable. Such as handpiece parts, electonic board, program, cooling and etc.

ADSS 1600W laser handle refurbishing Specifications:

Any more question please kindly let us know by whatsapp 0086-18518945778.

Model V Syneron laser handle repairing service

Syneron laser handle repairing service description

This F14358975 Syneron Medical Motif LHR Applicator Replacement diode stack is with 8 bars micro channel chips imported from Germany.It is used for Syneron brand of hair removal handle piece repairing and replacement.Oriental-laser focused on diode laser bar assembling for more than 16 years and we have seen various diode laser stacks.

Syneron Medical Motif LHR Applicator Replacement

Syneron laser handle repairing service Specifictaions:

Model No VS-MI-808-100-8-F14258975 diode head 800W
Application Syneron Medical Motif LHR Applicator Replacement
Operation Mode CW
Number of submounts 8 Bars
Power per submounts 100W
Central wavelength at 25℃ 808 ± 5nm
Maximum Operating Voltage 16 V
Fast Axis Divergence (FWHM) No
Slow Axis Divergence (FWHM) No
Expected lifetime >10000 hours
Typical pitch per bar 1.8mm
Cooling:
Flow rate 0.3L/min ±10% / bar
Water Temperature 15-25 ℃
Water Quality Deionized 2-10 µs/cm, mixed bed ion exchanger,particle filter<25µm

Syneron laser handle repairing service diode Dimensions:

Syneron Medical Motif LHR Applicator Replacement

 

Syneron laser handle repairing service Application:

This kind of F14358975 Syneron Medical Motif LHR Applicator Replacement diode head can be used for 810nm laser surgical equipment from syneron ike the following:

Syneron Medical Motif LHR Applicator Replacement

Any more question please find my whatsapp 0086-18518945778.

Model U 300W optic power laser handle replacement

300W optic power laser handle replacement description:

This 808nm hair removal handpiece model U is made of 6 bars laser stack with 300W optic power. The laser bars in this handpiece is similar with VS-MA-50-5-GTH. Differences: both positive and negative electrodes are on the top of the back side.

300W optic power laser handle replacement procedure:

Chioce A: Send the old broken handpiece to our facatory. We will do the process of checking , repairing, cleanning and etc. Then send the fresh new handpiece back to you.

Chioce B: if you have basic assambly capacity, you can send the diode laser stack only to our factory. We remove the old bar and mount the new bar to recover the laser power of the stack.

Choice C: Measure your stack and comfrim the water pipe hole and screw hole position. Then press the button below to buy a ready-made stack which is match your old hadnpiece.

300W optic power laser handle replacement Advantages

1.The newest Ausn mounting technology will be applied when repairing.

2.Diode laser bars are made in Germany

3.After repair. The handpiece will be as a new one. life time is much longer than before .

4.All technical support of hair removal machine is avaliable. Such as handpiece parts, electonic board, program, cooling and etc.

300W optic power laser handle replacement Specifications:

Any more question please kindly contact Danny whatsapp 0086-18518945778

Model S 810nm diode laser handle repairing for KES hair removal machine

810nm diode laser handle repairing for KES description:

This diode laser hair removal handpiece model S is made of 7 pcs diode bar(1 decorate bars and 6 real bars) with micro channel cooler. The diode laser bars in this handpiece is VS-MI-100-8-NL6-5, laser power 600W.

Whole handpiece is made in China.

Service mode: Repair the broken diode laser in the handpiece. Such as replace new laser stack, test TEC peltier, cleaning and so on.

810nm diode laser handle repairing for KES procedure:

Chioce A: Send the old broken handpiece to our facatory. We will do the process of checking , repairing, cleanning and etc. Then send the fresh new handpiece back to you.

Chioce B: if you have basic assambly capacity, you can send the diode laser stack only to our factory. We remove the old bar and mount the new bar to recover the laser power of the stack.

Choice C: Measure your stack and comfrim the water pipe hole and screw hole position. Then press the button below to buy a ready-made stack which is match your old hadnpiece.

810nm diode laser handle repairing for KES Advantages:

1.Save Money. Replace the broken diode stack only. Low cost and convenient

2.Long life time. we use diode laser bars from Germany. The newest Ausn mounting technology will be applied when repairing. After repair. The handpiece will be as a new one. life time is much longer than before

3.All technical support available. We major in diode laser mounting, software, spare parts over 16 years. All the technology are open to you.

810nm diode laser handle repairing for KES Specifications:

Any more questions please kindly contact Danny whatsapp 0086-18518945778.